Cannot Determine Insteon Engine
LOTSEVIL:(2) Access points / wireless phase couplers(4) Dual band devices installed(5) Dual band SwitchLincs in the box about to be installed.All is well with the bridging.I just ran signaling diagnostic and Exceeding max length of 5KB Home › iRule Builder › Insteon tsat Insteon tsat 62vetteefp Feb 05, 2014 07:27AM EST Had a connection with a wireless 2441zth. What do YOU want to VIEW today? There are newer versions and it is relatively painless to try, just in case.Perhaps temporarily getting an extension cord and powering the plm from the outletlinc might help identify the problem. his comment is here
cannot determine Insteon engine. DIYguy Average Member USA 60 Posts Posted-01/02/2014: 10:18:13 AM XTB-IIR (JV Digital Engineering)http://jvde.us/xtb_index.htmPhase coupler and X10 booster. Have you tried asking there? I tried the ADD an insteon device and also tried Discovery..
Isy Failed To Add Device Reason 3
I may not know what I'm doing when I start, but I will by the time I'm done. Manual switch operation is OK. Invalid email address Answer is required. Cobbled together a test line and hooked up one of the other same model OutletLincs I have in my "extras" box.
Loading... Does it communicate directly, no syncing between those 2 devices are necessary or is there a missing step in this process?any ideas? I've had it installed for many years now, replaced by passive phase coupler with the XTB. https://support.aartech.ca/index.php?/Knowledgebase/Article/View/161/2/isy994-message-cannot-determine-insteon-engine Back to top #7 LeeG LeeG Advanced Members 12,970 posts Posted 26 January 2013 - 06:06 PM Is that a 120v or low voltage Halogen?
Learn how Tapatalk'search and content recommendations can help you drive more traffic to your site. AARtech Canada Inc 2,681 views 1:49 Insteon Home Automation Kit Demo & Review | Damn Good Reviews - Duration: 9:09. Sat 01/26/2013 08:04:13 PM : Start Insteon Device Linking Mode Sat 01/26/2013 08:04:14 PM : [LNK-BGN ] 02 64 01 00 06 Sat 01/26/2013 08:05:36 PM : [LNK-STAT ] 02 53 In the console it showed the tstat in the ISY but the status was not shown.Tried to relink but it did not work so I removed the tstat from ISY and
- Back to top #9 paauto paauto Advanced Members 158 posts Posted 02 February 2013 - 05:04 AM I had the same problem last weekend wiring up some 2-wire devices. 2 of
- chucknewell HS2 / HSPRO 0 August 20th, 2005 09:48 PM All times are GMT -4.
- Dauguet HS MobiLinc WAF-AB8SS (3P) WeatherPLUG (3P)
- This switch is within 10' of a WAP.
The diagnostics are as follows: Fri 04/19/2013 10:12:55 AM : Start Insteon Device Linking Mode Fri 04/19/2013 10:12:55 AM : [LNK-BGN ] 02 64 01 00 06 Fri 04/19/2013 10:13:17 AM check this link right here now Not sure if this is a PLM issue or a device/load issue at this point. Isy Failed To Add Device Reason 3 Answers seem to point back to a problem with the device.I have had this outlet stop communicating before but power cycling it has corrected the issue in the past. Not sure it will make any difference.
LeeG 02/02 #6 I run Windows 7 with no comm issues at 4.3.26 nor 4.4.2 where I am now.What is the PLM type, 2412 or 2413, and what is the PLM this content espann 02/02 #5 I'm still having problems installing new devices, this time I have a new LampLinc Dimmer that I cant install, it just gives back: "Cannot determine Insteon engine", whether Topic New Topic Reply to Topic Printer Friendly Jump To: Select Forum News from Smarthome Announcements About Smarthome General Discussion Intercoms & Phones Insteon Lighting and Appliance Control Energy Saving I may not know what I'm doing when I start, but I will by the time I'm done.
If its under the two year warranty period and you suspect its dead.Please return it for a replacement.Teken . . . Sat 01/26/2013 08:05:57 PM : [INST-TX-I1 ] 02 62 1F C9 AD 0F 0D 00 Sat 01/26/2013 08:05:57 PM : [LNK-END ] 02 65 06 Sat 01/26/2013 08:05:57 PM : [Std Back to top #8 Bill Morrow Bill Morrow Member Members 16 posts Posted 26 January 2013 - 06:13 PM Lamp takes two 150W T3 bulbs. http://inviewsoftware.com/cannot-determine/cannot-determine-location-ios-7.html I had a very difficult time adding two brand new I2CS 2456S3 ApplianceLinc modules to my system.
Please don't PM with questions that can be asked in a forum. Light is a 300w Halogen, so power snb the issue. Comment Post Cancel aflink Junior Member Join Date: Sep 2014 Posts: 9 #6 09-27-2014, 05:43 PM After unlinking these two ISY can discover them as well.
Requires you start the process.
Any help would be greatly appreciated. Then go to each module you want to add and hold its set button until it is found. Within four minutes hold the set button on the responding device (the one on the left) until the first SwitchLinc stops blinking. Be a world saver.
Uses a double 220 15A breaker in the load center.PLM is new with ISY, 2413S dual band.Just went through the full process of clearing cache, checked firmware and now both read And, yes, it has not been firmly established that this is a communication problem. LeeG 01/11 #2 Try a Factory Reset of OutletLinc Dimmer before using New INSTEON Device to add it back. check over here Both need to be at the same level.
I tried reformatting the address again to 35 39 14. tools>diagnostics>event viewer and then set to level 3You should see this in the viewer:Inst TXInst RXInst SRXIf you don't see INST SRX after the first two then the device trying to By the time the ISY received the information about the Insteon Engine the device add process had already ended. Again got "Cannot Determine Insteon Engine".
Working... I have already added successfully several similar dimmers in other rooms. Saving energy is not always free.