Fix Cannot Desolder Dc Power Jack (Solved)

Home > How To > Cannot Desolder Dc Power Jack

Cannot Desolder Dc Power Jack

Contents

Any help is much appreciated. Thank you for this site and your help. I used to be able to desolder a 40 pin chip, install a 40 pin socket, and install a new chip in the socket in less than 5 minutes. Icydude21 July 31, 2008 | I just want to say thank you soooooo much for posting this guide and helping us with this problem. his comment is here

Everyone should read the part about the sleeves through the Mb,Very Importaint not to Damage the board. Tom April 12, 2008 | Thanks for the pictrorial instructions they have helped me tremendously. You can use high temps on board with low temp solder but, you have to be very quick as you run the risk of burning up the tracks. Chris-PC (17 I am about to hit up Radio Shack to buy the supplies and do it on my own. http://www.overclock.net/t/1314968/trouble-with-desoldering-dc-power-jack-on-my-laptop

How To Solder Motherboard Components

Then realized the power supply had burnt out. You don't want to destroy the mobo in trying to save money. I'm using a 40 Watt Weller soldering iron that goes up to 900 degrees and I'm trying to replace a DC power jack on a Gateway laptop.

  1. I think that they ought to paint tanks with that stuff. :) –AndrejaKo Jan 14 '12 at 1:03 A laptop of any recent vintage will have been manufactured with
  2. Find your laptop and download the maintenance and service guide, you'll find step-by-step disassembly instructions in there.
  3. Thats a little better but will eventually work loose.
  4. Then they told me that it would be better to just get a new computer instead of fixing it.
  5. Some laptops DC power jacks are quite difficult to de-solder.
  6. I have tried a 25w, and 40w iron and the Shack special 165w/230w soldering gun.
  7. Tampatec 599.727 visualizaciones 10:43 How to Disassemble any Laptop in Under 20 minutes - HP DV6000 - Duración: 19:17.
  8. The design is intrinsically flawed.
  9. I think standard rosin core solder will work just fine. 3.
  10. It's necessary to take a closer look at the power jack.

Luke March 21, 2008 | Hi, Great tutorial…definatly gave me some confidence boost :P. This friggin jack took me HOURS. So the laptop actually gets power but will not start? Rob Meyer October 6, 2008 | I replaced my dc jack and I tested the continuity and it beeps on my meter.

Acción en curso... Desoldering Braid Jesse October 11, 2008 | Thank you very much for your tutorial. Assemble everything on your desk, connect an external monitor, plug in the power adapter and turn on the laptop.

asked 4 years ago viewed 7385 times active 2 years ago Related 3Repairing SATA motherboard connector: Advice needed0Acer Laptop does not power up after repairing DC power jack-2Where can I buy

Good as new. thanks Nick February 9, 2008 | Thank you for the tutorial. The center pin of the plug was TINY and therefore HIGHLY prone to breaking. Full Review Fractal Design Define Mini C - Black - Windowed Reviewed by Duality92 Hey fine people of OCN!

Desoldering Braid

He uses it only for homework. https://answers.yahoo.com/question/?qid=20091111151206AAYH0gs Since my machine was out of warranty, I did it myself.
I decided not to even attempt to resolder it, since the previous attempts only lasted a few months. How To Solder Motherboard Components I hope you get compensated for the laptop.my instructor taught me to do the thorough diagrams too and multiples as you dig down into the layers. Desoldering Gun Be careful.

You are the Greatest man alive. this is a five pin DC jack and know matter what I try it just will not come off. Thanks……..looking forward to your help again. If you use a traditional soldering iron / station, you will not be able to melt the solder on the power jack of a motherboard. How To Desolder

It is a fragile corner. Just use a pair of needlenose on the half-piece, apply heat and voila. Reply Reply post #9 of 13 10/12/12 at 1:08pm cdoublejj 4.0ghz Joined: Aug 2009 Location: MO, USA Posts: 9,799 Rep: 233 (Unique: 193) Reviews: 4 Trader Rating: 35 weblink I agree that desoldering the plug was the hardest part.

Always keep spares. K the file clerk February 26, 2008 | o dear pitty thank you its actually functining now (although i may have killed my internet card in the process….) thanks though ! could it be my CPU?

Make sure the power supply is not dead and outputs correct voltage. 2.

As soon as I turn ON the notebook, and the external power is connected, the notebook switch automatically over to battery power. Its copper colored, sometimes its called solder braid. Sorry to pick nits but you should never use a soldering GUN on a laptop motherboard. Took apart the laptop and could see an indication of a short next to the positive pin of the power connector.

I only bought the machine for $350 so it didnt seem worth it. Now I need to clean off the old solder and add new solder. Does this laptop has motherboard problem or power (DC) jack problem? I have ordered a new cord for it and will wait until it arrives.

I researched and assumed it was the same common problem and came across this site. Best Home Security System? At this point I have removed the legs entirely and I'm left with blocked holes. You think they really need this many fasteners to hold together a 8lb piece of plastic ;-)?

John Gammell 1.602.118 visualizaciones 3:20 Desoldering 1 - Duración: 1:38. Am I approaching this completely wrong? The offical Toshiba fix is to do this and then run a bead of hot melt glue around the connector. HP knew this and designed it that way for a reason, so they could make money on repairs.

The jack itself looks like ti has 4 prongs that are affixed to the motherboard via glue and 5 points that are soldered in. Rob March 10, 2008 | I tried a brand new power adapter. Cambiar a otro idioma: Català | Euskara | Galego | Ver todo Learn more You're viewing YouTube in Spanish (Spain). I cannot use the notebook with external power anymore.

So with that said it is experience and technique, a good soldering gun just helps you get more done and allows you to d o numerous units or soldering takes a wtf January 18, 2008 | im trying to do this and it is going well so far, but two screws on the base will NOT come out. I might try next time.While it wasn't a hard swap, I was appalled to see the internal design of those little HP's that wal-mart sold for 399 a few years back. Then it stopped charging my battery and would not run the computer with the battery removed.